Top 10 typical forklift mishaps ， forklift procedure must take notice of these issues ！.

Don't take too lightly the forklift at the office. If the procedure is bad, there will certainly be serious accidents in minutes, and there are numerous mishaps including forklifts.

Situation 1: The forklift freight obstructed the vehicle driver's view, and the individual ahead can not be discovered, causing a moving mishap.
Situation 2: In order to preserve the balance of the forklift when lifting heavy goods, the employees used their body weight as the weight, which virtually created casualties.
Instance 3: The size of the forklift freight surpasses the allowable width of the course and holds on the roadside rack, which nearly triggers an accident.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift driver did not notice the pedestrian, and the pedestrian did not see the forklift.
Situation 6: The forklift lifts the personnel unlawfully, the forklift motorist does not use the seat belt, the forklift lifter drops and the chauffeur is crushed when the forklift surrender.
Situation 7: The forklift chauffeur did not wear a safety belt and fell from the lorry when it surrendered and was crushed.
Forklift procedure must take note of these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after confirming that there are no barriers that impede the safety of driving, beep the horn first and afterwards start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge need to be safe prior to starting.
3. When the forklift begins with a load, the motorist should initially confirm that the tons is stable and trusted.
4. The begin has to be sluggish and constant.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the mast ought to be slanted backward. .
2. Do not raise the fork too high when driving. When going into and leaving the work site or while driving, beware that there will certainly be no obstacles overhead. When the lots is traveling, the fork needs to not be elevated expensive, which will impact the security of the forklift. .
3. After unloading, the fork must be decreased to the normal driving setting prior to driving. .
4. When transforming, if there are pedestrians or vehicles nearby, the driving signal must be released initially. High-speed sharp turns are restricted. High-speed doglegs will certainly create the vehicle to lose lateral security and topple. .
5. When the forklift is downhill, it is purely forbidden to turn off the flame and slide, and it is prohibited to brake instantly while driving with loads unless there are special situations.
6. When the forklift is running, it needs to comply with the website traffic rules in the manufacturing facility and must keep a certain safety distance from the car in front. .
7. When the forklift is running, the load should be in the lowest setting that does not hinder the driving, and the gantry must be effectively slanted back. The lots will not be elevated other than when stacking or loading. .
8. The height of the load must not obstruct the vehicle driver's view. In unique scenarios, when the product impacts the forward vision, drive at a low speed when reversing.
9. It is restricted to activate the ramp, neither to drive across the ramp. .
10. The safe driving speed of the forklift in the manufacturing facility location is 5 km/h, and it should drive safely at a low rate when going into the production workshop area. .
11. When the forklift is raised, raised or driven, it is prohibited for personnel to stand on the fork to hold things and play a stabilizing role. .
12. If problems are located, they will be repaired and reported in a prompt way, and they will never ever run with diseases or hide them.

packing and discharging.
1. When fork-loading items, the range between both forks must be adjusted as required to make the tons of the two forks well balanced and not skewed, and one side of the thing must be against the shelf. .
2. It is prohibited to collaborate with a single fork or use a fork top or draw. In special conditions, security indication should be established to remind bordering pedestrians. .
3. In the process of packing and dumping products, the forklift must be stopped with the brake. .
4. The rate of the automobile should be sluggish and steady. Beware not to roll the wheels on the dunnage, so as not to stretch the rolled items and injure people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under Electric Forklift Truck for Warehouse the load, and it must be kept in mind that the fork idea need to not touch other items or objects. The tons needs to be stabilized with very little back tilt of the gantry to make sure that the load does not move in reverse. The mast can be tilted onward slightly when the tons is decreased to allow for simple positioning of the lots and extraction of the forks. .
6. It is prohibited to fork items at high speed and hit hard items with the fork head. .
7. When the forklift is functioning, it is restricted for people to stand around the fork, so as to stay clear of the collapse of the goods and injure people. .
8. Overloading is restricted, and it is forbidden to make use of forks to lift personnel to take part in high-altitude operations to stay clear of high-altitude falling mishaps. .
9. It is not enabled to use the brake inertia to Stand-on Electric Pallet Stacker slide, place, round or roll objects. .
10. It is not enabled to utilize forks to pick, turn pallet discharge.

Leaving .
1. It is restricted to leave the forklift when the things on the fork impend. Before leaving the forklift, you should dump the goods or lower the fork frame.
2. Pull the hand brake handle to dead or depress the emergency brake button.
3. The engine is switched off and the power is cut off. (Except for special scenarios, such as the vehicle driver does not leave the car's view and does not go beyond 1 minute).
4. Remove the secret. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the look needs to be inspected, and fuel, lubing oil and cooling water must be included.
2. Check the safety efficiency of starting, running and braking.
3. Examine whether the lights and horn signals are full and reliable.
4. During the operation of the forklift, examine whether the pressure and temperature are typical.
5. After the forklift is running, the outside leakage should additionally be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine prior to leaving the automobile;.
2. When you experience someone before you during driving, you need to send a signal at a distance of 5 m;.
3. The driving rate in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be too sharp to stop the tendency of "free switching";.
6. Running up and down the incline must be slow and consistent, and no turning on the incline is allowed.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the vehicle must be driven backwards when worsening;.
8. When the forklift personnel lug the goods and move forward, if they run into big or hefty goods and most likely to the driver's view, they should take the turning around workout
.
The "Eight Prohibitions" ought to be adhered to in the operation.
1. Solitary fork procedure is not allowed.
2. It is not enabled to raise the goods for cross country driving.
3. It is not permitted to grab the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other hazardous chemicals with forks.
5. It is not enabled to make use of inertia force to get the goods.
6. It is not permitted to use braking pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work with the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive side to side on slopes
.
Auto parking is not allowed under the following conditions.
1. Curves, narrow roadways, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an challenge on one side of the road, the contrary side of the area with the very same size as the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844